FCC certification mark used method and FCC warnings

If FCC is Certification, the nameplate must have FCC ID:
The authentication device FCC ID and equipment other information indicated on the nameplate on the. On the FCC ID number representation is not specified, but FCC is recommended in the ID number around crossed to compare it with other information distinction, such as: FCC ID: x x x 123
With FCC ID nameplate in the certification process may be asked to modify, in order to prevent waste, in formally accredited before, proposal applicant not printed in large numbers with FCC ID nameplate or in silk screen products, carving.
Device on a prominent position marked with this paragraph of the following statement:
This device complies with part 15 of the FCC Rules . Operation is subject to the following two conditions: (1) This device may not cause harmful interference, this device and (2) must accept any interference received, including interference that may cause undesired operation.
If the device has two or more components, connected by cable, sales as a whole, the statement above as long as the standard in the main control part. If the equipment is too small, marking the area is insufficient, the statement can be written in the user manual or the instructions for use of the significant position, or marked in the equipment box.
Intentional transmitters user manual or the instructions should also remind users: without approval of equipment to change or modify it, users of the equipment use rights may be eliminated. If the user manual or the instructions not to paper mode of delivery, such as the disk or through a network such as the mode of delivery, this information must also be included, so that users get the information.
FCC certification mark used method
If FCC is DOC, the nameplate must have FCC LOGO:
If the device is tested proved to comply with FCC regulations, shall use the following labels:
The label format ( Declaration of conformity )
If the personal computer are made separately certified parts assembled, the personal computer is not required to be tested, using the following assembly description tag:
The label format, assembly ( Declaration of conformity )
If the equipment is too small or the label on the device on the practice work, such as CPU motherboard or in-line circuit board peripheral devices, product identification labels can be marked on the user manual or the instructions for use of the significant position, however, the only identification information ( trademark and model) and FCC marking must be marked on the product.
The label should not use the stick type paper labels, the label should be permanently attached to the device, and the consumers can easily and clearly see the label. Permanently attached refers to the content on label etching, engraving, printing, screen printing or printing on the apparatus body so that it can't erase, or metal, plastic or other material, welding, riveting or label to a permanent adhesive in the form of fixed on the apparatus body. Label design should take into account in the environment in which the service life of equipment.
Class a digital device or a peripheral user manual prominently with the following statement or a similar statement:
Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules . These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment . This equipment generates, uses and can radiate radio, frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications . Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.
Class B digital device or a peripheral user manual prominently with the following statement or a similar statement:
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules . These limits are designed to provide reasonable protection against harmful interference in a residential installation . This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications . However, there is no guarantee that interference will not occur in a particular installation . If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio / TV technician for help.
If the device is composed of a plurality of digital equipment, more than two statement only needs to be included in the main control unit can be used. If the manual or paper-based user manual is not provided, but to a disk, Internet and other means are provided, the statement above should also take corresponding the way to give users.
FCC warnings
If FCC Verification, nameplate and instructions were to be warnings:
The verification mode when, the products must have the following labels:
The label format ( validation)
The label must include models ( for example: Model . No. 123 ), the company name or trademark ( Company ' s name or trade name ), the country of origin ( Country of origin ) information. According to the United States Customs and the Federal Trade Commission ( Federal Trade Commission ) regulations, all outside of the United States products must be marked with country of origin.
In any case, according to the authentication labels on the products are not appear FCC ID number.
The label or manual should be similar to describe:
This device complies with Part 15 of the FCC Rules . Operation is subject to the condition that this device does not cause harmful interference. ( applicable to such as Part 73 radio equipment radio receiver)
This device is verified to comply with Part 15 of the FCC Rules for use with cable television service. ( applicable to cable and connectors )
This device complies with Part 15 of the FCC Rules . Operation is subject to the following two conditions: (1) this device may not cause harmful interference, this device and (2) must accept any interference received, including interference that may cause undesired operation. ( all other equipment )
Note: if the device is connected by wires to the two or more than two parts, labels should be affixed to the above main control unit. If the equipment is too small, can not paste the above statement, it must be in equipment packaging or instructions embodied in the above statement.